How to Fix a Toaster That no Longer Engages?

How to Fix a Toaster That no Longer Engages?

How to fix a toaster – This is a simple guide that will show you how to fix a toaster that no longer engages.

Ready to leave home for work? But before you decide to respect the tradition. You put your bread in the toaster to get a crispy sandwich loaf. Unfortunately, the lever on your machine does not engage!

It’s valuable; you won’t be able to enjoy your lunch and will probably waste time trying to make it work. Before considering replacing it, you can check if bread crumbs have not accumulated in your toaster, which can prevent it from engaging.

Worse, their accumulation obstructs the movement of the trolley. It can cause the heating elements to short out, clogging the lockout lever and interfering with the operation of the solenoid.

Toasters are relatively simple devices to repair, and you can therefore try to restore them when they no longer engage. It allows you to save money and take action toward environmental protection.

How Does a Toaster Work?

Before giving you advice on how to repair your toaster, a little reminder of how it works.

The device contains nichrome wire which conducts electricity, producing energy that turns into heat and warms everything around it, including bread. Toasters are built to shut off on their own to prevent your bread from getting completely burnt.

When you add the bread, a cage at the bottom of the slot holds it. You have to push the lever down to lower it ultimately. The toaster allows electricity to flow through the heating elements, toasting the bread. Then spring and a latch hold the lever in the down position.

Bread isn’t the only thing that gets heated by the heating element: many parts of the toaster are too. One of these parts is the trigger mechanism, designed to change shape as its temperature increases.

If any of these parts are malfunctioning, it may prevent the device from engaging.

Examine the outer cable

Before you pull out your screwdriver, you need to look closer at the outer cable that comes out of the toaster. Look for signs of damage. For example, if it has been in the water for a long time, it may corrode and not transmit power to your device.

In particular, you should pay specific attention to the connection between the cable and the toaster. If you find the cord loose, or you can see all its wires exposed, that’s likely the culprit. It is not easy to replace the cord of a toaster; if this is the case, you may need to purchase a new device.

Ridding Your Toaster of Crumbs

Continued use of your toaster may cause it not to switch on. Some appliances use an electro-magnetic mechanism that holds the lever in the down position until the timer or thermostat restarts the toaster. Bread crumbs can stick to the electromagnet and cause it to malfunction. As a result, your toaster will not engage!

To fix it, no need to open your device. Pull out the crumb tray and shake the toaster lightly to release the crumbs. Do not hesitate to turn it over to remove as many crumbs as possible.

Once the debris is out, try operating your toaster again. If it doesn’t snap, find a fan or device to blow air and dislodge any residue that’s still stuck on.

Deep Clean

If, after this express cleaning, your toaster still does not switch on, it is time for a thorough cleaning.

Open your device by removing screws and other snap-on parts. Once the toaster opens, you will notice a spring-like part attached to the lever mechanism. This spring part may be dirty, which may cause the failure to engage.

The spring allows the lever to lock and release your loaves. If it’s rusted, your toaster won’t engage. A spring that appears discolored or degraded should be replaced.

  • Determine what type of spring your machine contains and find an appropriate replacement part
  • Remove the old toaster spring
  • Place the new one and check that it works correctly

Take the opportunity to check the condition of the hook and other electronic components. Be sure to remove the last little bits of bread you see and thoroughly clean all other items. You can use a can of compressed air to spray the inside of the toaster several times, then close the toaster.


If these different cleaning steps prove unsuccessful, you must call on your repair skills.

Using a multimeter, check the condition of the electronic components. Start with the electromagnet! It is he who supplies the heating resistor by closing the electrical circuit. If this component malfunctions, unsolder and replace it.

If your toaster is old, the magnet may be worn out. The lever hits the magnet so many times that the latter finally gives way. Generally, you will need to take a screwdriver and remove the lever to access this component. Once you find the magnet, you need to remove it, put it back in place, and reassemble the toaster.

Examine if the resistors are operational and their leads are not touching or close together. Check the condition of the connections and clean them if you notice traces of burns. Perform this operation with a fine file.

The other element to examine is the electronic board. Its failure results in a toaster that no longer engages. Unfortunately, this is proving impossible to repair, and you must replace it with a new one.

To Protect Yourself!

It would help if you always put safety at the top of your priorities when working on your toaster. There are several ways to achieve this. First, always unplug the device before you start working on it if you don’t want to run the risk of electrocuting yourself.

Second, you should wear proper protection when working on your toaster. For example, you can wear protective gloves and goggles when working inside the machine. This way, you can prevent debris from cutting or flying into your eyes.

Remember to call in a professional if you cannot repair your toaster yourself.

It can be frustrating to have a toaster that won’t engage, especially when you’re craving a loaf of bread. Fortunately, there are ways to prevent this from happening.

How to Fix a Toaster That no Longer Engages?

First, you need to be gentle with your toaster. It is not necessary to push the lever of the device every morning, and a simple press is enough.

Second, you should also clean your toaster regularly. If you can keep crumbs from building up inside your toaster, you’ll prevent them from getting in the way of your magnet.

Besides, you can also prevent the crumbs from overheating in the toaster, which can go a long way in protecting the internal workings of your device.

Finally, it would help if you kept the cord out of the way of puddles of water. If you prevent moisture from accumulating around the cable, you can avoid its degradation.